WEBENCH® Tools: Tina-TI Convergence Problem
Tool/software: WEBENCH® Design ToolsHey,Everyone ,I have made this schematic on Tina-TI but I am not getting a convergence problem.which i am not getting why ,the expected result is 12V @ 10 A output...
View ArticleTIDA-00961: TIDA-00961
Part Number: TIDA-00961Hi,I am giving 100V AC input to the board, but i am not connecting any load. I am running the code in Build 3 mode(both current and voltage loop closed), initially switching is...
View ArticleTIDA-01093: Low side FET design considerations
Part Number: TIDA-01093In TIDA-01093, it was noted that the DSG/CHG controlled FETs are on the PACK- / Low side.Customer's system designs usually put the FETs on the high side, so that the PACK- / GND...
View ArticlePMP21529: Back Up Supply mode Vbus
Part Number: PMP21529Hi E2E,Good day.During the back-up supply mode of the PMP21529, I understand that the Vbat range is between 38-55V. However, the Vbus is known to be Vbus_nominal - 0.5V, how can we...
View ArticleWEBENCH® Tools/BQ40Z60: BQstudio GOLDEN IMAGE
Part Number: BQ40Z60Tool/software: WEBENCH® Design ToolsHi, I'm trying to get a golden image to serial flash. I have done the next steps:1-Chem ID programming 2-Learning Cycle3-Export .gg file and...
View ArticleWEBENCH® Tools/LM5088: LM5088 buck boost inverting from +24V to -20V...
Part Number: LM5088Tool/software: WEBENCH® Design ToolsI have created a design using WEBENCH using the LM5088.Vin =14-32VDCVout = -20VDCIout max is 3.5ADCThe WEBENCH design states to use a 33uH...
View ArticleClik here to view.
PMP10979: Implement adjustable output voltage
Part Number: PMP10979Per reference design PMP10979 using LM5119 in parallel, is there a recommended add-on circuit perhaps to the FB2 node that allows some limited output voltage adjustment from 5V to...
View ArticlePMP20660: What is the purpose of D2?
Part Number: PMP20660Hi teamMy customer asked about the use of D2 (B170-13-F) in the PMP20660 circuit.What is the purpose of D2?
View ArticleWEBENCH® Tools/TPS82150: TPS82150
Part Number: TPS82150Tool/software: WEBENCH® Design ToolsHi,as defined in TIDA-01405 design, TPS82150 can be used as negative voltage source.However the simulation model (both for TINA and PSPICE) does...
View ArticleClik here to view.
CC110L async mode usage
Tool/software: WEBENCH® Design ToolsThe Tx/Rx devices of our existing products use the 433.92MHz ASK module.Therefore, the RF of CC110L needs to be OOK.We purchased and acquired the TI TrxEB and CC11XL...
View ArticleTIDA-01604: Need TIDA-01604 and TIDM-1007 Firmware
Part Number: TIDA-01604Hi, Need firmware of TIDA-01604 and TIDM-1007, so that I can refer it in my pfc project. Thanks and regardsIshtiyaque Ahmad
View ArticleWEBENCH® Tools/OMAP-L138: OMAP-L138:...
Part Number: OMAP-L138Tool/software: WEBENCH® Design ToolsHiError happens. A message dialog is copied to TI_07.I reeasrch some of WEB site, and arranged a file(c:\ti\ccs910\ccs\eclipse\eclipse.ini), Is...
View ArticleWEBENCH® Tools/TPS55160-Q1: Working issue with 5V
Part Number: TPS55160-Q1Tool/software: WEBENCH® Design ToolsI have used TPS55165-Q1 Buck-boost converter, our input voltage range 5V to 24V. The problem is that at the input of 5V we didn't get any...
View ArticleClik here to view.
WEBENCH® Tools: WEBENCH Allegro Connector
Tool/software: WEBENCH® Design ToolsHello,During install after I paste the my own licence key, I got message the key is invalid..What could be the problem while the key is just copy paste from the...
View ArticleWEBENCH® Tools/LM2731: Webench Model for LM2731Y
Part Number: LM2731Tool/software: WEBENCH® Design ToolsHi team, Do we have an available model for the LM2731Y (0.6MHz) version? We have a version for the X device, but we would like to model the Y...
View ArticleClik here to view.
WEBENCH® Tools/CC1310: 868 MHz Inverted F Type Antenna Design Issue
Part Number: CC1310Tool/software: WEBENCH® Design ToolsHello All,I am designing a custom hardware where i am using "CC1310_RHB(S-PVQFN-N32)" MCU package.For designing I am referring to the " Design...
View ArticleClik here to view.
TINA:Not able to create Macro for PSPICE file
Hello Team,I am facing trouble while creating the macro for EPC8004 spice model in TINA. I can see the following error. Kindly help me to fix this issue.Thanks (Please visit the site to view this file)
View ArticlePMP15002: Information about the Common Mode Inductor used L1
Part Number: PMP15002Hi,I am doing research on this design and trying to locate various parts from the BOM of the PMP 15002. One part that I cannot find is the common mode inductor with the reference...
View ArticleClik here to view.
Designing DC to DC converter
This is a transient response analysis of flyback converter that I'm working with but what is this ringing in primary current and what creating it?(Please visit the site to view this file)
View Article