Unable to install pspice for TI due to Access key usage
Hi, I downloaded the tool before and had been actively using it.Recently I cleand my PC and tried to re-install pspice for TI. But Installer shows error as 'Too many machines attempting to...
View ArticleTIDA-00609: Need Rev.G schematic file
Part Number: TIDA-00609We need the schematic of TIDA-00609G but I only find the schematic of Rev.F.Could you provide me the schematic of Rev.G?
View ArticlePSPICE-FOR-TI: Install PSpice on non-internet computer
Part Number: PSPICE-FOR-TIHello, my work computer does not have an internet connection. How can I still install PSpice?Thank youJoe
View ArticleTIDA-00951: source code and technical advice
Part Number: TIDA-00951Hello TI,we are very much interested in using your TIDA-00951, 2-KW, 48 to 400V, reference design in our design Circuit .1. Can you please say what are the requirements2. Can we...
View ArticleTIDM-02002: What is the formula to calculate the value of the low-pass filter...
Part Number: TIDM-02002There is a low-pass RC filter based on R254 and C245 with 56.2Ohm and 10pF accordingly. This gives roughly a cut-off frequency at 283MHz.What is the calculation formula or a...
View ArticleTIDEP-01017: MMWCAS-DSP-EVM + MMWCAS-RF-EVM cascade radar application with...
Part Number: TIDEP-01017Other Parts Discussed in Thread: MMWCAS-DSP-EVM, MMWCAS-RF-EVMHello!I use MMWCAS-DSP-EVM + MMWCAS-RF-EVM in cascade radar mimo application with network connection to another...
View ArticleCan a general company produce a TI jtag emulator(XDS200, XDS560)?
Other Parts Discussed in Thread: ENERGYTRACE, C2000WARE, LAUNCHXL-F280025CDear TIHow do I build or produce a jtag emulator(XDS200, XDS560) in a general company?I wonder if they will receive development...
View ArticlePMP8711: Capacitor charging circuit topology
Part Number: PMP8711Hello,I want to design a capacitor charger.The input is 18-36V, Output voltage is 42V, output current is 0.9A and output capacitance is 27mF.Also output current and voltage must be...
View ArticleClik here to view.
TIDA-01604: Current loop bandwidth
Part Number: TIDA-01604In design guide, 3.2.3.4.2 said the voltage loop bandwidth is about 10hz. But the bandwidth of the current loop is not introduced in 3.2.3.2.2. So I want to know what is the...
View ArticleTIDA-010042: Using reference design with direct resistive load connected and...
Part Number: TIDA-010042Other Parts Discussed in Thread: SM72442We are currently looking for a MPPT solution to directly power a resistive load (2.7 Ohm, 1000 Watt max power rating at 48V) from two...
View ArticleTIDA-010015: EMI/EMC Filter Design
Part Number: TIDA-010015Can I use same EMI filter (which has been used in this Design) for my 85-264AC input to 12V,25V output AC/DC converter?
View ArticlePSPICE-FOR-TI: UCC2897A
Part Number: PSPICE-FOR-TIOther Parts Discussed in Thread: UCC2897AHello, Dear!Could I get PWM controller UCC2897A SPICE mode for TINA simulator?Thanks
View ArticleTIDA-00317: design tool for level sensor
Part Number: TIDA-00317hi team,do you have any design guide or design tool for LEVEL Sensor, REFERENCE LIQUID Sensor, REFERENCE ENVIRONMENT Sensor?we have no knowledge on how to select this sensor for...
View ArticleXDS110 no response
Other Parts Discussed in Thread: AWR1642Hi, everyone ! I bought one XDS110 from mouser electronics. However it has no response after connecting PC. D1/D2 LED is always off. I bought on AWR1642...
View Articleusing PC_dsp_test_dl_algo.out to simulate is not the same as the results from...
when the custom layer run in PC emulation mode by PC_dsp_test_dl_algo.out, the results is correct. But, when it run in board, the results are incorrect. what has caused this?
View ArticleWireless charging
Hi team,Charge current 150 mA, voltage: 4.2 to 5 V.Customers need a wireless charging solution, best for cost-performance, and also the coil area is not too large. Which one should be more suitable...
View ArticleTIDA-050047: Copper thickness
Part Number: TIDA-050047Hello can you confirm the copper thickness for this design?
View ArticleClik here to view.
TIDA-010031: Configuring OPAmp output and ADC input on the same pin
Part Number: TIDA-010031Hi All,For the TIDA-010031 board I am configuring pin 1.2 as -ve, pin 1.3 as +ve inputs of the opamp & pin 1.1 as output of the Op-Amp. Same pin 1.1 is configured as the...
View ArticlePMP11237: Parts alternative
Part Number: PMP11237Hi team,Good day.In the PMP11237 reference design, it was noted in the schematic that you need to turn on S2 after power on to enable LLC and PFC operation. Does it mean that you...
View ArticleTIDM-02002: TIDM-02002 questions
Part Number: TIDM-02002Hi team,Customer plan to develop a bi-directional PSU, and they are interested in TIDM-02002 reference design.They have some questions for TIDM-02002 reference design:1) Is the...
View Article