WEBENCH® Tools: Capacitor selection for high-pass filter: NP0 or.... X7R????
Tool/software: WEBENCH® Design ToolsI was taking a look to application note (sorry, I don't remember which one) where there was an high-pass filter stage with 0,1 Hz cutoff frequency.I need to design...
View ArticleClik here to view.
WEBENCH® Tools/TPS54320: TPS54320 about switching frequency
Part Number:TPS54320Tool/software: WEBENCH® Design ToolsHi,Let me talk about frequency that can be set in the webench.I entered the following conditions into webench.・Vin=9V -...
View ArticleWEBENCH® Tools: Thermal Simulation on Custom Device
Tool/software: WEBENCH® Design ToolsIs it possible to create a WEBENCH thermal simulation for a section of a custom device? In other words, how can I draw my own layout for a single device and create a...
View ArticleWEBENCH® Tools/TPS56C215: Schematic Edit
Part Number:TPS56C215Tool/software: WEBENCH® Design ToolsHi everyoneI'm a FAE intern in RTW team and I have a confuse point about WEBENCH Desgin Tools.I want to edit a schematic not only change the...
View ArticleUV led application
Hi, I am working on a consumer product that needs to brighten and dim a UV led which runs at 3-3.3 V at 10 mA. The circuit just needs to brighten and dim the LED every 5 seconds or so in order to...
View ArticleWEBENCH® Tools/TPS54160: TPS54160
Part Number:TPS54160Tool/software: WEBENCH® Design ToolsCan a discontinous conduction mode simulation be performed with a buck converter on webench tool?
View ArticleWEBENCH® Tools/LMZ23603: LMZ23603
Part Number:LMZ23603Tool/software: WEBENCH® Design ToolsI have the following power requirements.Vin (minimum) = 9VVin (maximum) = 30VVout = 5VIout (maximum) = 2AOperating temperature (maximum) = 30C.I...
View ArticleClik here to view.
TIDA-00120 unable to open schematics
Hello TI,I'm trying to duplicate this solar charger, and i was unable to open the schematic with eagle version 8.3.0, OrCAD pspice 17.2. I wonder what would be the best software to use to open the...
View ArticleWEBENCH® Tools/LMR16010: Can LMR16010 output stable 15V ?
Part Number:LMR16010Tool/software: WEBENCH® Design ToolsThe input voltage is 42VDC and I want to get 15VDC / 1A output. But WEBENCH cannot output a solution on LMR16010. Is it a problem about WEBENCH?...
View ArticleClik here to view.
WEBENCH® Tools/TPS61087: Ask for help about WEBENCH stimulation with two...
Part Number:TPS61087Tool/software: WEBENCH® Design ToolsCustomer use TPS61087(Step-Up DC-DC Converter) for simulation, input voltage is 5V ,output voltage is 12V. From the datasheet we can see maximum...
View ArticleLM5122: Webench simulation question
Part Number:LM5122Hello, Below is LM5122 condition. But customer can not simulate by this condition on Webench. Has any problem for it? Does LM5122 support this power? Thank you....
View ArticleClik here to view.
WEBENCH® Tools/TPS53355: same load transient graph for different number of...
Part Number:TPS53355Tool/software: WEBENCH® Design ToolsDear Team,Simulation type=Load transientwhen i run simulation for 1.1V with 28A in load transient case i observed same load transient graph for 3...
View ArticleWEBENCH® Tools/WEBENCH-POWER-DESIGNER: Total copper area after changing...
Part Number:WEBENCH-POWER-DESIGNERTool/software: WEBENCH® Design ToolsTeam,How do i find out what the total copper area of the PCB is after changing the copper model in the Thermal simulation tool on...
View ArticleWEBENCH® Tools: TL5500
Tool/software: WEBENCH® Design ToolsHi,I would like to get more information on TL5500, such as S-parameters.Thanks,Ali
View ArticleWEBENCH® Tools/WEBENCH-POWER-DESIGNER: Worst Case Analysis Results...
Part Number:WEBENCH-POWER-DESIGNERTool/software: WEBENCH® Design ToolsTeam,How is the cross over frequency being calculated in the worst case analysis tool. After re-compensating this design i only...
View ArticleWEBENCH® Tools/TLV62130: Inductor selection about Lower bound and Upperbound
Part Number:TLV62130Tool/software: WEBENCH® Design ToolsWhen I design TLV62130 circuit with WEBENCH, the default lowerbound and upperbound of inductor IDC is 5.506A and 10A.How is this value...
View ArticleWEBENCH® Tools: On the temperature characteristics of WEBENCH and parts
Tool/software: WEBENCH® Design ToolsHi,My customer has a question.Does the operation value of WEBENCH and the simulation result, and the chart also include the temperature characteristics of parts?Best...
View ArticleClik here to view.
WEBENCH® Tools/LMR23630: WEBENCH Simulation
Part Number:LMR23630Tool/software: WEBENCH® Design ToolsHello ThereI wanted to verify my calculations for the LMR23630 with the WEBENCH Design Tool. As I have read in the forum, that this should be...
View ArticleClik here to view.
WEBENCH® Tools: Advanced Charting - Default change suggested
Tool/software: WEBENCH® Design ToolsHi,My customer made me aware of some room for improvement, that I completely agree with, so please find our suggestionfor a new Default view of the Webench Advanced...
View ArticleWEBENCH® Tools/TPS40211: TPS40211 SEPIC circuit simulation
Part Number:TPS40211Tool/software: WEBENCH® Design ToolsHi Sir,I want to simulate TPS40211 Vin=4.5-52V, output=5V/3A.but WEBENCH can't run, pls help...
View Article