WEBENCH® Tools: xx
Tool/software: WEBENCH® Design ToolsHi.I must design an isolated switching step up from 24V to 160V -150mA...what do you suggest ?Wich device to start from ?Thanks.Mario.
View ArticleClik here to view.
TIDA-01442: are DA4_P/M and DB4_P/M signals swapped on the FMC connector?
Part Number:TIDA-01442DA4 is connected to DP12_M2CDA5 is connected to DP10_M2CDA6 is connected to DP8_M2CDA7 is connected to DP9_M2CShouldn't DA4 be connected to DP11_M2C?DB4 is connected to...
View ArticleClik here to view.
TIDA-01573: The measured output rising edge is rather slow
Part Number:TIDA-01573Hi,I am using the TIDA-01573 board. But the measured output rising edge is rather slow. What is the problem? Is the FET damaged? Or my measurement method is wrong?The 1st pic is...
View ArticlePMP7390: PMP7390 latest Rev
Part Number:PMP7390Hi, is there any latest Rev for PMP7390 (PCB/Gerber/Schematic) ?May I know if the shared files (dated May 2012) are the only available revisions? If there are newer...
View ArticleClik here to view.
TINA/Spice: NCP5181
Tool/software:TINA-TI or Spice ModelsI am trying to import the spice model fro NCP5181 to TI TINA. The model is from here: https://m.onsemi.com/support/documents?type=Models&rpn=NCP5181Following...
View ArticleTIDA-01022: DCLKout12P/N length match with F_refclk1_P/N
Part Number:TIDA-01022does DCLKout12P/N need to match length with F_refclk1_P/N? On the ADC12DJ3200EVM the DCLKOUT8_P/N matchs the FPGA_JESD_CLK_P/N
View ArticleTIDA-01022: LMK04828 SYNC input
Part Number:TIDA-01022the TIDA-01022 uses SYNC_SE to synchronize LMK04828 and the ADC12DJ3200EVM uses LMK04828_SYNC from FPGA. what is the differences between those two approaches.
View ArticleTIDA-00120: Programming and Heatsink questions
Part Number:TIDA-00120I'm back on this design and have some questions:I don't see a programming header for the MSP430 on the design. Am I missing it, or do I need to add a header, then use something...
View ArticleTIDA-00725: Temperature monitor for APD
Part Number:TIDA-00725I am trying to build a laser range finder based on the APD and its biasing circuit and amplification circuit in TIDA-00725. The APD biasing circuit design is not clear to me. Why...
View ArticleCCS/TIDA-01292: overcurrent protection
Part Number:TIDA-01292Tool/software: Code Composer StudioHi shreenidhi,The link you provided is not opening...
View ArticlePMP11670: How to modify PMP11670 to 4.2A/5A total output (2.1A/2.5A each port) ?
Part Number:PMP11670Hi,May I know how to modify PMP11670 to 4.2A/5A total output (2.1A/2.5A each port) ? Current design is 2.0A (port1) +1.5A (port2). Since LM73605RNPR already outputs 5A, is changing...
View ArticleTINA/Spice/ISO1211: TINA 9 model error
Part Number:ISO1211Tool/software:TINA-TI or Spice ModelsHi,just downloaded the ISO1211 transient simulation and want to run transient analysis, but TINA (9.3.100.244 SF-TI) complains:"Missing syntax...
View ArticleTINA/Spice/TPS54318: Simulation of both part number using single tool.
Part Number:TPS54318Tool/software:TINA-TI or Spice ModelsI want to perform power sequencing simulation using these two part numbers i.e TPS54318 and TPS7A9001DSKT.Please suggest any tool which can...
View ArticleClik here to view.
WEBENCH® Tools/WEBENCH-POWER-DESIGNER: Optimization options: High efficiency...
Part Number:WEBENCH-POWER-DESIGNERTool/software: WEBENCH® Design Tools
View ArticleWEBENCH® Tools/TIDA-01385: Can the battery in TIDA-01385 be recharged?
Part Number:TIDA-01385Tool/software: WEBENCH® Design ToolsCan the battery in this design be recharged?A Schottky Diode is used before the battery. So, the battery can not be recharged, right?
View ArticleTINA/Spice: BQ79606-Q1
Tool/software:TINA-TI or Spice ModelsIs it possible to simulate charging and discharging if a cell in TINA-TI ??
View ArticleWEBENCH® Tools/TPS7A90: Unable to perform simulation of part number in...
Part Number:TPS7A90Tool/software: WEBENCH® Design ToolsI want to perform the simulation for TPS7A90/TPS7A9001DSKT using webench power design tool. when I enter the part number it shows part number...
View ArticlePMP4435: Transformer and Inductor Design
Part Number:PMP4435Dear Sir,Could you please share the mathcad file for the PMP4435. what is the (Magnetic flux density) Bmax considered for the transformer(T1) design and Output Inductor (L1) design...
View ArticlePMP8750: lowest adjustable output current in PMP8740 2kW charger
Part Number:PMP8750Hi Team,I received the following request, can you help?######################################What is the lowest adjustable output current in PMP8740 2kW charger Project?Can I set...
View Article