WEBENCH® Tools/LM5155: WEBENCH design not created
Part Number:LM5155Tool/software: WEBENCH® Design ToolsHi all While trying to create a WEBENCH design with the LM5155 with these (... or similar ...) parameters:Vin=5V ... 6VVout=50V, Iout=1A I get...
View ArticleTINA/Spice/INA129: How to convert TINA model into LTSpice model
Part Number:INA129Tool/software:TINA-TI or Spice ModelsI converted the PSpice model (for tool TINA) into LTSpice model (file txt with all coordinate) according to the following tutorial:...
View ArticleTINA/Spice/LMG3410R070: Simulate Drain Slew Rate with PSpice/TINA-TI
Part Number:LMG3410R070Tool/software:TINA-TI or Spice ModelsWe want to simulate the behavior of the LMG3410 with different RDRV resistances. For the simulation we did use the given example PSpice and...
View ArticleClik here to view.
TINA/Spice/UCC21710-Q1: Look like the pspice model has a problem. I was...
Part Number:UCC21710-Q1Tool/software:TINA-TI or Spice Models
View ArticleClik here to view.
TIDA-01093: TIDA-01093
Part Number:TIDA-01093Dear All: I design the 20s BMS as the TIDA-01093， I have 2 question about the TI design. As below shown 1. I think the MCU SDA , CLK signal can through the Q9,...
View ArticleTIDA-00120: Can I use this solution for Lithium Ion batteries?
Part Number:TIDA-00120Hi ,Currently I am using TIDA-00120 design for 12V/24V Lead acid batteries. Can i use this same design for Li-Ion / LiFePO4 batteries of same voltage? Please suggest me on this....
View ArticleTIDA-010047: About FET for SR
Part Number:TIDA-010047Hello E2E,Please le me know about TIDA-010047.I suggested this reference design to customer. They were interested in it. If possible, I want to do recommend TI's Nch-FET to them....
View ArticleTINA/Spice: Open-loop and closed-loop of CMOS inverter
Tool/software:TINA-TI or Spice ModelsDear TI,I design Pierce crystal oscillator circuit. I face a problem to calculate gain and phase of CMOS inverter.How to build a test bench to calculate open-loop...
View ArticleMSP430 controlled Texas instruments EV2400 HPA500 problem
Dear TI,Good day.We are using the tool board of the above product. (MSP430 controlled Texas instruments EV2400 HPA500)we didn't have any special problems. However, the error and the problem occurred as...
View ArticleTIDA-00121: Can i this solution? for Charging the Li-ion battery
Part Number:TIDA-00121Hi Can we use the TIDA-00121 for charging the Li-ion Battery?
View ArticlePMP20199: Output Voltage going above desired value at Start up
Part Number:PMP20199Hi Expert,I have implemented a 54V 30W power supply using the UCC28700. The supply has another secondary winding for 4V output. When observing the start up both the outputs, the 54V...
View ArticleTIDA-01476: TI Designs: TIDA-01476 : Query on WiFi networking of TI design
Part Number:TIDA-01476Hello Support Team,Refer the TI design TIDA-01476. It is based on RF networking.Is it possible to use this design via WiFi networking? I have a WiFi modem. I wanted to access this...
View ArticleWEBENCH® Tools/TL760M33-Q1: TL760M33Q1 Design Parameters
Part Number:TL760M33-Q1Tool/software: WEBENCH® Design ToolsHiI have Used TL760M33Q1 in my design to bring 24v to 3.3v directly. I am having a problem in its output voltage. It giving 2.1v something....
View ArticleTIDA-01471: ADC output decreases with increasing frequency
Part Number:TIDA-01471Hello,We are evaluating some samples of the TIDA-01471 and get some confusing output we cannot explain. Some plots and the used jumper settings are shown in the attached .pdf...
View ArticleTINA/Spice/SN74LVC1G74: SPICE model available yet?
Part Number:SN74LVC1G74Tool/software:TINA-TI or Spice ModelsHello,I wanted to see if a SPICE model had been created for this part yet. I was unable to find one through the TI website. Is there one...
View ArticleWEBENCH® Tools/TPS57040-Q1: Difficulty selecting / opening desired project...
Part Number:TPS57040-Q1Tool/software: WEBENCH® Design ToolsWhen I go to "My Designs", scroll down to the desired project and click on "Open" the project I've selected doesn't open, it will generally...
View ArticleClik here to view.
TIDA-01606: UCC5320S schematic question
Part Number:TIDA-01606Hi,I have several questions for the schematic below:1. why need 10ohm(R33) for the primary side 3V3, but not needed at the secondary side 12V and -5V? And why R33 is chosen to be...
View ArticleTINA/Spice/AWR1243: Can I simulate the AWR1243 model using IBIS model in TINA
Part Number:AWR1243Tool/software:TINA-TI or Spice ModelsHi,There is an IBIS model of AWR1243, how can I import it to TINA? and what all simulations I can do? Please share if any related documents are...
View ArticleTIDA-00120: Issues in 48V system
Part Number:TIDA-00120Hi,I was changed the modifications what you suggested for 48V system from 12V System.1. MOSFETS Q2,Q3,Q4,Q5 150V rated2.Resistor divider networks for PV,BV (2.8V )3. Software:...
View ArticleTIDA-00366: Power Supplies
Part Number:TIDA-00366Hi, I see you used two power supplies in this design. One 16V and another 5V. Why didn't you make 5V from 16V rail? what was the point for having two supplies?Thank you
View Article