Part Number:TIDA-070002
Hello Daniel,
Hope you are well.
Given that the max output load current from the TIDA-070002 could be 10A, why did you choose a coupled inductor
with a secondary winding rated at 10A. If the TIDA-070002 were supplying 10A, then the average and peak inductor current will be higher.
As an example, if the output load current is 7.3A, then the average and peak secondary-winding inductor currents would be 11.6 and 13.8A respectively.
Kind Regards,
Rajan.
Part Number:TIDA-00281
Hi,
We have an application to run 60V/250W BLDC motor for EV.
We have prepared one schematic to do so by taking reference of TIDA-00281.We have also done some of the modifications and also not included lots of parts which is not necessary for us.
I want some expert from TI provide schematic review for attached file.(Please visit the site to view this file)
Part Number:TIDA-010132
Hi TI,
I was going through the TIDA-010132 schematic and find that it is powered from a separate custom board.
Block diagram for that power board is shown on page 29 of TIDA-010132.
Block diagram and selected components, looks very promising to me and I will love to use the power tree architecture and selected components in our company projects.
Can you guys share us the schematic of TIDA-010132 POWER Board?
Thanks,
Lalit
Part Number:TIDA-010042
Hello,
Could the nice TIDA-010042 be tailored to perform as MPPT Wind Turbine Charger?
In wind turbines must be used a diversion style regulator: which charges the batteries, and as the batteries become charged, the excess power is diverted to a resistive load.
Wind turbines are not designed to work with PWM or shunt style solar panels chargers controllers wired between the wind turbines and the battery bank
These controllers “disconnect” the solar panels rom the battery bank when the batteries are charged, allowing te wind turbine to spin free, which is not recommended.
Thanks,
Part Number:LMG3410R070
Tool/software:TINA-TI or Spice Models
I want to know about the variation of Vsd vs Isd curves of LMG3410R070 with Vgs for third quadrant operation.
Part Number:TIDA-00961
Champs,
I am asking this for our customers.
Do we have power loss information of the major parts of TIDA-00961?
At least the power loss information about the TI GaN?
Wayne
Part Number:TIDA-00281
Hello,
I am looking for a reference software for the design TIDA-00281, I have found tidcbd2 file, which includes some files from the motorware at path:
E:\sw\modules\hal\boards\TIDA-00281\f28x\f2802x\src, as per path it can be observed that it related to motorware path, but inside the
path:C:\ti\motorware\motorware_1_01_00_18\sw\modules\hal\boards, there is no such folder name as a TIDA-00281.
Part Number:LM5180
Tool/software:TINA-TI or Spice Models
I appreciate your support in providing me LM5180 which can be simulated in TINA promptly. The model is working fine in TINA but it taking a very long time for running even 5mS transient analysis. Is there a way to speed-up the simulation process viz. enabling additional cores of my PC's processor, etc.?
Part Number:OPA445
Tool/software:TINA-TI or Spice Models
I'm running noise simulation of OPA445 using Tina simulation package. I suspect that the simulation model is not accurate by comparing with in data sheet. But the data sheet only provides the voltage noise down to 10Hz and no flicker current noise. Other mfgs provide down to 0.1Hz. Do you have more accurate model? Any suggestions how to evaluate noise performance
Part Number:LMZ20502
Tool/software: WEBENCH® Design Tools
Using Webbench my 5V to 3.3Vdc circuit puts out 4.1V. The resistor values suggested Rfbt= 232K in parallel with 12pf and Rfbb= 51.7K
What causes this error? Is there a minimum load for this part? There is 22uF on the output and it is lightly loaded. The mode pin is grounded.
Part Number:TIDA-01173
Hi,
Customer is asking to get board file and schematic of TIDA-01173 reference board.
Please help to provide, thanks!
And other question is we saw there is compensation schematic for OPT9221 (COMP_MOD_REF & COMP_MOD_FB).
Is it necessary?
Part Number:PMP11536
In the PMP11536 USB-C DFP + 5V2A Power Bank With Input Fast Charger Reference Design on TI Design
http://www.ti.com/tool/pmp11536
MSP430G2332 MCU controls the BQ25895 and TPS25810,
Could you send for me the source code of PMP11536, please?
I saw same subject but the response was about PMP4496
Best regards
Part Number:LM5104
Tool/software:TINA-TI or Spice Models
Hello everyone,
I am trying to control the LM5104 with an external voltage (pulse generator) in the pin IN to control 2 gating signals. According to what I understood, when there is high level in IN pin you get high level in OH and low in LO and vice versa.
The left part of the circuit is the one included in the datasheet. The right part is my circuit, where I want to control the voltage coming to the diode, either -50V or 1V. In this simulation in TINA I always get -50V in the diode. The idea is to connect a pulse generator in IN pin, so the diode will be directly polarized only in certain cases. -50V is in the pin I_PIN_EN_OL. Best regards,
Part Number:LM43601
Tool/software: WEBENCH® Design Tools
Hi,
Good day.
Our customer noticed that the schematic design output for LM43601 and LM43601-Q1 is different. Although the BOM shows the same parts.
They use the following parameters:
Vin = 20V -30V
Vout = 18 V
Iout = 1A
Also, they share the webench design that they have. You can click the link below to view it.
LM43601: webench.ti.com/.../SDP.cgi
LM43601-Q1: webench.ti.com/.../SDP.cgi
Please advise.
Thank you.
Regards,
Cedrick
Dear forum, Im developing a energy meter system and I need a IC PGA that allow me to read differential signals, so it needs to have differential input as well differential output. I would like to know if TI sell any PGA with this specs: differential intput and differential output.
Part Number:LMR14030
Tool/software:TINA-TI or Spice Models
Hello,
I have performed some simulations for the LMR14030 on the online workbench tool. However, i would like do some simulations in TINA-TI and I am unable to download the TINA model. The export to TINA functionality on the workbench is not working and I am only able to install pspice models that don't work in TINA. Any help would be greatly appreciated.
Thanks,
Morgan
Part Number:LM5050-2
Tool/software:TINA-TI or Spice Models
Was running simulation on TI spice Using LM5050-2 for Oring of two power supply on one Load . When i try simulate lost of one power input, the Gate voltage of the other IC is affected. Cannot understand why. The simulation result shows that VG1 gate voltage is affected which i think it should not be . thanks
(Please visit the site to view this file)