Part Number:TIDA-010030
HI am looking for Tida-010030 Eval Board source code for Msp Microcontroller which has been used in same Board.
Secondly CAN h/w is also present in that design, is CAN communication working in source code? If yes please help to share memory map.
Rohit
+918141616356
Part Number:LM76003
Tool/software: WEBENCH® Design Tools
Hello,
I'm trying to see a design that was shared with me.
I can't see it, tried changing IP's, computers and browsers.
The link I got in my mail: Link
this is what I get after 6.7 minutes:
An error occurred while processing your request.
Reference #30.1da9645f.1555934093.1519bf4a
Tool/software: WEBENCH® Design Tools
Is there a problem?
Part Number:UC1823
Tool/software:TINA-TI or Spice Models
Hello,
I'm actually using PSPICE with the encrypted model UC1823. I have a problem with the pin RAMP that generates a sawtooth of 0V to 2.8V instead of 0.8-1V to 2.8V. It seems the Vvalley is not considered in this model and the sawtooth doesn't change at all with a high duty cycle ( > 50%). It's impossible to analyze the impact of the sub-harmonics by using slope compensation because the saw tooth doesn't change at all. Do you know if a UC1823 model has been developed for PSPICE?
Thank you very much,
Jeremy
Tool/software: WEBENCH® Design Tools
Hi,
I'm trying to design a multi output power supply for a battery powered audio device. I need to supply +15, -15, +5, and +48 volts. First of all does anyone have any suggestions or experience with this type of supply? Also would it be wise to clock all of the regulators together and if so how would I go about that. It just seems to me that having 4 regulators running at different frequencies seems like I'm asking for trouble as far as noise goes. As you can probably tell switching supplies aren't my strong suit.
Thanks,
Ken
West End Recording
Part Number:TIDA-00663
Part Number:TIDA-00281
Hi,
Is anyone have simulated this gate driver with Power Mosfet on Pspice. As I want that file for reference to check the results. If anyone have done kindly provide.
Part Number:TIDA-00778
Hello,
In TIDA-00778 design, we can see a anti aliasing filter with cutoff frequency of 15 MHz. The picture below shows this filter:
Also, the following picture shows the ADC input impedance model for TMS32028027F.
So, I have some questions about that:
1-)How do you choose the 15 MHz for cutoff frequency of anti aliasing filter? as far as I know, the cutoff frequency of anti aliasing filter should be smaller than half of sampling frequency and the current sampling frequency in FOC algorithm is 10-20 kHz. so the cutoff frequency of anti aliasing filter should be smaller than 5-10khz.
2-)How do you calculate the 15 MHz?
3-)When we need this filter?
Regards,
Mohammad.
Part Number:PMP9253
Hi TI
Can we change the power transformer to PA5130.005NL to support 5V/6A output?
Any other BOM change needed?
Fortinet, Colbert Hsu
Part Number:J6EVM5777
Tool/software:TINA-TI or Spice Models
Hi Texas Instruments,
what are the HAL camera changes (hardware / ti / dra7xx / camera) to test camera OV10635 sensor (Capturing through LVDS camera)
knowing that Linux kernel has driver for FPDlink serializers and deserializers(ti_fpd3_serdes) .
Regards,
Ala
Part Number:TIDA-00834
Hi Team,
Would you please share the PHI controller board schematic with me?
Thanks!
Roy Hsu
Part Number:TPS7A33
Tool/software: WEBENCH® Design Tools
Hi to all,
I have designed a TPS7A3301KC -6.1V ... 5.5V to -5.00V @ 0.8A a with the tool.
The report (attached), including the simulation results, shows a circuit successfully designed. I am convinced that the circuit is ok for my needs but the Safe Operating Area graph is wrong or, at least it is incomplete, I mean: as you can see in the graphic included in the report, the line (in gray), which should represent the operating point, is not present and the current value of 1A is present from -3V to about -4.3 V, while for a more negative values towards -4.7 V the current drops to 0, while it should be different ... in fact, inside the range - 5.6V ... - 6.1V the report (consistently with the data-sheet) states that the output current is OK, and finally the input voltage range is completely out of the graph.
Thank you
Regards
Davide Ba(Please visit the site to view this file)doni
Part Number:PMP4486
Dear TI Experts,
The input capacitor used is 100uF (C3) in the input side of the power supply, instead of 100uF can I use lesser value like 10uF as bulk capacitor, because even if the input capacitor is not sufficient to supply the entire current for the power supply, it can be supplied by the external source ( source power supply / battery) and to reduce the input ripple current we can use additional ceramic capacitors with lesser ESR like 2.2uF two or more numbers accordingly.
As per documents and waveforms every cycle the input capacitor is getting discharged and charged for normal operation of the converter. But in many brick modules or small size converters the input capacitor used are very less, Is it because of the lesser track length or board size, same way can we keep very less values like around 10uF instead of 100uF.
Regards,
Nesh
Tool/software: WEBENCH® Design Tools
Hi,
I'm struggling a little bit here with the LM3880DBV circuit usage in a multi rail power supply that I generated in the Webench tool.
So, here is my power supply circuit:
And this is how I sequenced my circuit:
My problem is I don't know where to put the sequencer circuit in my main schematic, before or after the outputs? As in the above schematic, it looks like the sequencer has to be connected to the end of the last output which is so confusing!!!! While in the LM3880DBV datasheet it seems to be placed before the generated outputs, as shown here:
I'm so confused here! Please, any help!?
Tool/software:TINA-TI or Spice Models
hi,
there might be a bug in my TINA (v. 9.3.150.328 SF-TI Simplified-Chinese). When two or more capacitors are cascaded, the DRC will fail, reporting "pin 1 of capacitor is float, and the point is not connected to ground", and inconsquence I cann't do DC voltage analysis or AC analysis.
would you mind have a look at this problem? thank you!
Part Number:TIDA-01512
Hi TI team,
I am presently implementing the multiphase reference design from TI in my LS2 based project. I have installed the GUI but I am not able to find out the PWM controller IC (TPS53681) in the fusion GUI. So please let me know how to get the device in the list of devices supported by the GUI so that I can program the NVM of the PWM controller.
Hi :
How do I set the serial number using the tool and Can I download the program with JTAG? Thanks.
