Part Number: TIDA-01464
Tool/software: Code Composer Studio
I am testing the reference TIDA-01464 and I want the spec of the components: L101, T201, T202.
↧
CCS/TIDA-01464: Spec of flyback and Inductors
↧
CCS/TIDA-00961: Memory range error
Part Number: TIDA-00961
Tool/software: Code Composer Studio
Can you explain what's happening with the memory range error shown below?
Thanks.
↧
↧
TIDA-010024: Trouble Understanding Where 6LoWPAN Mesh Example Code Sends RF and UART Data
Part Number: TIDA-010024
Hello,
I am currently using the TIDA-010024 software on the CC1312 Launchpad. I have been able to get the project (which is called 6LoWPAN_Mesh_TI_15_4_cc1312_tirtos_ccs)to function properly using the debug_push and debug_root_push build configurations. I've attached a screenshot below to show the UART output on a serial terminal connected to the board running the debug_root_push configuration.
However, I have a custom board using the CC1312 and I would like to alter the code slightly to send some different data. The trouble is, I can't seem to find where in this particular project the data is actually being constructed, transmitted, received, and printed over UART. I have searched many files and have even tried the "C/C++ search" function and can't find where the UART in the figure above is being printed. I have worked with simpler projects and was able to alter those files to do what I needed, but I am fairly new to this mesh code interface and it doesn't seem to work the same way as these simpler projects.
If possible, can somebody point me to the correct files I should be looking at in order to change what data is sent over RF and the UART data that is sent as well? Any help is greatly appreciated.
Thanks,
Grady
↧
TIDA-00645: BLDC Motor does not move
Part Number: TIDA-00645
I'm following the reference design to try to move TelcoMotion DT4260 BLDC motor (from the DRV8308 kit) using 1PWM mode. While the firmware successfully built and flashed apparently with MSP-EXP430G2 board, the motor did not run. The red PWRGD led on the TIDA-00645 continuously emits dimmed red light; the hall sensors receive power and output correctly, but there appear to be no power to the phases of the motor.
Please help me get the reference design working. As of right now, we think there might be issues within the firmware code - which is the one we downloaded from the reference design web page today. Is the reference design code confirmed to be working normally? If there is an updated version, please share it with me.
Thank you very much.
↧
WEBENCH® Tools: TINA software
Tool/software: WEBENCH® Design Tools
Hello Dear
we need to buy original and full version of Tina software ,,How much is it and how can I ordered this software version from your company ???
thanks a lot in advance
↧
↧
WEBENCH® Tools/UCC28180: UCC28180
Part Number: UCC28180
Tool/software: WEBENCH® Design Tools
Many of your tools such as, a) Webench power designer b) UCC 28180 design calculator Revision B (XLS file)gives entirely different component values for the same specification of 1000W PFC at 45kHz. Kindly suggest the recommended tool as soon as possible.
↧
WEBENCH® Tools/TMS320F28379D: getting error in simlink file
Part Number: TMS320F28379D
Tool/software: WEBENCH® Design Tools
i have getting following error in my board, if i solve this error, i am getting another error as failed to generate binary output.
The following error occurred during deployment to your hardware board:
Debug Server Scripting (DSS) error:
*** User inputs:
Target Configuration: C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/F28379~1.CCX
Program Name: C:\Users\MAHESH~1\DOCUME~1\MATLAB\SPEED2~1.OUT
Board Name: *
CPU Name: C28xx_CPU1
Hardware Name: TI_Delfino_F2837xD
*** Starting debug session...
C28xx_CPU2: GEL Output:
Memory Map Initialization Complete
SEVERE: C28xx_CPU2: Failed CPU Reset: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU2: Trouble Reading Register PC: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU2: GEL: Error while executing OnReset(1): Internal error while writing 0x0005FB00@Data
at *((int *) 0x5FB00)=0 [f28377d_cpu2.gel:28]
at OnReset(1)
SEVERE: C28xx_CPU2: Trouble Writing Memory Block at 0x5fb00 on Page 0 of Length 0x2: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU2: Error occurred during flash operation: Target failed to write 0x5FB00@Program
SEVERE: C28xx_CPU2: Trouble Writing Memory Block at 0x5f800 on Page 1 of Length 0x2: (Error -1137 @ 0x5F802) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU2: Error occurred during flash operation: Target failed to write 0x0005F800@Data
SEVERE: C28xx_CPU2: Trouble Writing Memory Block at 0x5fb00 on Page 0 of Length 0x2: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU2: Error occurred during flash operation: Target failed to write 0x5FB00@Program
*** Debug Session Name: Texas Instruments XDS100v2 USB Debug Probe_0/C28xx_CPU1
*** Board Name: Texas Instruments XDS100v2 USB Debug Probe_0
*** CPU Name: C28xx_CPU1
*** Connecting to target...
C28xx_CPU1: GEL Output:
Memory Map Initialization Complete
SEVERE: C28xx_CPU1: Failed CPU Reset: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Trouble Reading Register PC: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Trouble Writing Memory Block at 0x5d122 on Page 1 of Length 0x2: (Error -1137 @ 0x5D124) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: GEL: Error while executing OnReset(1): Target failed to write 0x0005D122@Data
at *((long int *) 0x5D122)=0xA5A50000 [f28377d_cpu1.gel:28]
at OnReset(1)
SEVERE: C28xx_CPU1: Trouble Writing Memory Block at 0x5fb00 on Page 0 of Length 0x2: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Error occurred during flash operation: Target failed to write 0x5FB00@Program
SEVERE: C28xx_CPU1: Trouble Writing Memory Block at 0x5f800 on Page 1 of Length 0x2: (Error -1137 @ 0x5F802) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Error occurred during flash operation: Target failed to write 0x0005F800@Data
SEVERE: C28xx_CPU1: Trouble Writing Memory Block at 0x5fb00 on Page 0 of Length 0x2: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Error occurred during flash operation: Target failed to write 0x5FB00@Program
SEVERE: C28xx_CPU1: Failed CPU Reset: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Trouble Reading Register PC: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: Trouble Writing Memory Block at 0x5d122 on Page 1 of Length 0x2: (Error -1137 @ 0x5D124) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 6.0.407.3)
SEVERE: C28xx_CPU1: GEL: Error while executing OnReset(1): Target failed to write 0x0005D122@Data
at *((long int *) 0x5D122)=0xA5A50000 [f28377d_cpu1.gel:28]
at OnReset(1)
SEVERE: Target reset failed. Error: 1
SEVERE: Error reseting target: Target reset failed. Error: 1
org.mozilla.javascript.WrappedException: Wrapped com.ti.ccstudio.scripting.environment.ScriptingException: Error reseting target: Target reset failed. Error: 1 (C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/RUNPRO~2.JS#121)
at org.mozilla.javascript.Context.throwAsScriptRuntimeEx(Context.java:1693)
at org.mozilla.javascript.MemberBox.invoke(MemberBox.java:160)
at org.mozilla.javascript.NativeJavaMethod.call(NativeJavaMethod.java:204)
at org.mozilla.javascript.optimizer.OptRuntime.callProp0(OptRuntime.java:119)
at org.mozilla.javascript.gen.c1._c0(C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/RUNPRO~2.JS:121)
at org.mozilla.javascript.gen.c1.call(C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/RUNPRO~2.JS)
at org.mozilla.javascript.ContextFactory.doTopCall(ContextFactory.java:340)
at org.mozilla.javascript.ScriptRuntime.doTopCall(ScriptRuntime.java:2758)
at org.mozilla.javascript.gen.c1.call(C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/RUNPRO~2.JS)
at org.mozilla.javascript.gen.c1.exec(C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\toolbox\target\SUPPOR~1\tic2000/CCS_CO~1/RUNPRO~2.JS)
at org.mozilla.javascript.tools.shell.Main.evaluateScript(Main.java:503)
at org.mozilla.javascript.tools.shell.Main.processFileSecure(Main.java:425)
at org.mozilla.javascript.tools.shell.Main.processFile(Main.java:391)
at org.mozilla.javascript.tools.shell.Main.processSource(Main.java:382)
at org.mozilla.javascript.tools.shell.Main.processFiles(Main.java:179)
at org.mozilla.javascript.tools.shell.Main$IProxy.run(Main.java:100)
at org.mozilla.javascript.Context.call(Context.java:528)
at org.mozilla.javascript.ContextFactory.call(ContextFactory.java:450)
at org.mozilla.javascript.tools.shell.Main.exec(Main.java:162)
at com.ti.ccstudio.apps.internal.scripting.RunScript$1.run(RunScript.java:88)
Caused by: com.ti.ccstudio.scripting.environment.ScriptingException: Error reseting target: Target reset failed. Error: 1
at com.ti.debug.engine.scripting.Target.reset(Target.java:622)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
at java.lang.reflect.Method.invoke(Method.java:606)
at org.mozilla.javascript.MemberBox.invoke(MemberBox.java:145)
... 18 more
↧
PMP7410: PMP7410: Parameters of transformer?
↧
WEBENCH® Tools/LM2576S-ADJEVM: LM2576 WEBENCH don't have Negative voltage output reference?
Part Number: LM2576S-ADJEVM
Tool/software: WEBENCH® Design Tools
Hello:
LM2576 WEBENCH don't have Negative voltage output reference?
could you give me -15-12-5 output Reference schematic?
by th way
could you give me Application Note about Buck IC to negative voltage output?
THKS
↧
↧
TIDA-00961: TIDA-00961
Part Number: TIDA-00961
Hi,
In auxillary power supply why you are setting for 13.4V it should be 12V ?. The screenshot of same attached below.
Thanks
yashwanth
↧
Product folder not found
Hi E2E,
Good day.
Our customer can't find the product folder of the TIDA-00067 and the 24VDCPLCEVM on the website, are these redirected to other links or it was already removed in TI website?
I'm hoping for your confirmation? Thank you.
Regards,
Carlo Cabaccan
↧
PMP15006: Secondary Side Voltage too low
Part Number: PMP15006
Dear all,
I have been trying to build a circuit according to the PMP15006 reference design.
The design parameters are as follows:
- One isolated output at 5V, max. 250 mA.
- Small board layout
- Input from 24V standard industrial rail
During testing I experienced that the Voltage at the secondary side never exceeds 2.4V. And during operation, the Coil gets very hot so I have to cut power.
As far as I can say I followed the schematic of the reference design. The PCB layout is different. You will find those attached.
Any help is appreciated,
Björn Ellensohn
(Please visit the site to view this file)
↧
TIDA-00540: ALTERNATE DESIGN TO TIDA-00540
Part Number: TIDA-00540
Hello,
It seems "TIDA-00540" is obsolete.
And the IC's in the above reference design are also non stocked.
Can any please suggest me the alternate design for the TIDA-00540.
Thanks & Regards
Kalyan
.
↧
↧
CCS/TIDA-00951: TIDA-00951-SW - download not possible
Part Number: TIDA-00951
Tool/software: Code Composer Studio
Hi,
I've would need to software download for TIDA-00951, the link on the webside is broken "It looks like we’ve encountered some resistance". Could I get the software from other appropriate approach? Waiting for feedback!?
Thanks
Simon
↧
WEBENCH® Tools/TPS53647: Selectable number of phases
Part Number: TPS53647
Tool/software: WEBENCH® Design Tools
Hello Team,
1) is it possible to adjust the number of phases for a TPS53647 design? Webench only allows 4 phases designs?
2) If I enter Vin=12V, Vout=1V, Iout=30A from the product page http://www.ti.com/product/TPS53647 I get a message that no valid operation point can be found.
Thanks and Best Regards,
Hans
↧
WEBENCH® Tools/LM5010: Lm5010 doesn't seem to work with power designer
Part Number: LM5010
Tool/software: WEBENCH® Design Tools
No matter what parameters i enter into webench power designer for the LM5010 I get the message "Design cannot be created. Your preferred device doesn't work with the inputs you selected"
Is there a known issue with this part?
↧
TPS2120 Spice simulation
I am considering TPS2120 for a new design and want to simulate it. Unfortunately TI only provides an encrypted PSpice model for this part, which prohibits me from simulating in LTSpice as I normally would. One would expect that TI at least provides models for their own Tina TI simulator, but apparently not.
I found an old forum post e2e.ti.com/.../756523 where someone from TI attached a TINA model for this part (TPS2120_TRANS.TSC).
I tried importing this model using these instructions: www.ti.com/.../slva527.pdf
The model seems to compile ok in the first step, although I have my doubts since the editor doesn't show much valid text. The new macro wizard is however not able to import this file.
Anyone can help me out?
↧
↧
TIDA-01604: relay
Part Number: TIDA-01604
Hello. I'm Jung Jae-yup, studying with an interest in circuits.
I would like to ask a question about TIDA-01604.
As you are studying, please understand the level of questions.
When I look at the TIDA-01604's datasheet, I read that it sounds when the relay goes above 70Vrms.
The part I want to study is to know the flow chart of the relay.
For example, in the schematic, I would like to know which relay should receive a signal from the control card and which signal should come in through which device.
Thank you for answering every question.
I would like to ask a question about TIDA-01604.
As you are studying, please understand the level of questions.
When I look at the TIDA-01604's datasheet, I read that it sounds when the relay goes above 70Vrms.
The part I want to study is to know the flow chart of the relay.
For example, in the schematic, I would like to know which relay should receive a signal from the control card and which signal should come in through which device.
Thank you for answering every question.
As you are a student who wants to study, it will be hard, but please answer in detail It would be much more appreciated if you can explain it by name like U1, J601, T1, etc
↧
CCS/TIDA-01469: Motor Monitoring Using Wireless Vibration Sensor Reference Design Enabling Preventive Maintenance
Part Number: TIDA-01469
Tool/software: Code Composer Studio
I am not able to run the example code. Specifically, SimpleBLEPeripheral_motorMonitorWakeup function in simple_peripheral.c is able to return when the system starts. But in the second time that it is triggered by a timer, this function does not return. Problem 2, the example code seems to not enable power saving, it is always working with a current around 65mA.
↧
WEBENCH® Tools/FILTERPRO: FilterPro DT
Part Number: FILTERPRO
Tool/software: WEBENCH® Design Tools
I have used FilterPro DT in the past for differential MFB low pass filter design. I have recently switched from Windows 7 to Windows 10 and when I installed FilterPro DT it is able to run the Wizard but at completion, no other action can be taken. The program appears non-responsive. No options are active. I tried to use the Webench tool but i do not find differential filter support available in it. I have installed FitlerPro DT from the TI site on two different machines both running windows 10 with the same result.
↧